Custom Wood Stove Glass | R10 Pattern Cut
Engineered for extreme direct-flame environments, this custom-cut 3/16" R10 pattern cut Pyroceram ceramic glass panel delivers commercial-grade thermal endurance for specialized heating stove doors requiring an angled sloped top line paired with a clipped lower-left corner bevel. While standard glass easily fractures under continuous firebox temperatures, our high-performance wood stove glass tolerates continuous operating temperatures up to 1256°F and transient thermal spikes up to 1400°F without cracking or structural fatigue.
Whether you require a precision wood stove glass replacement or a resilient transparent barrier for specialty pellet, coal, or high-output gas stoves (exceeding 18,000 BTUs), each R10 panel is custom-cut to your supplied five-point dimensions within tight ±1/16" workshop tolerances. This transparent ceramic glass maintains an airtight combustion seal, restoring heating efficiency while preserving a clear view of your firebed.
Product Features
- R10 Pattern Cut Geometry: Multi-point custom profile featuring an angled sloping top edge, two parallel vertical side runs of differing heights, a flat bottom run, and an angled lower-left clipped corner.
- Genuine Pyroceram® III: Commercial-grade 3/16" (5mm) transparent ceramic glass engineered specifically for direct flame contact.
- Extreme Thermal Shock Resistance: Rated for continuous heat up to 1256°F (680°C) with short excursions to 1400°F (760°C).
- Amber Transparent Tint: Classic high-temperature crystalline composition with a subtle warm amber/bronze undertone.
- Safety Seamed Edges: Factory-chamfered edges remove razor-sharp cutting burrs for safe handling during installation.
- Appliance Versatility: Ideal for multi-faceted wood stoves, fireplace inserts, pellet units, and coal heaters requiring an R10 silhouette.
- Expedited Fabrication: Custom-cut, inspected, and securely packaged to ship within 4-5 business days.
Product Specifications
| Material Formulation | Pyroceram® Transparent Ceramic Glass |
|---|---|
| Thickness | 3/16" (5mm) |
| Geometric Profile | Pattern R10 – Sloped Top with Clipped Lower-Left Corner |
| Max Continuous Temperature | 1256°F (680°C) |
| Max Short-Term Thermal Shock | 1400°F (760°C) |
| Coefficient of Thermal Expansion | Near-Zero (~0.0 × 10⁻⁷ /°C) |
| Color / Tint | Transparent with faint warm amber/bronze undertone |
| Cutting Tolerance | ± 1/16 Inch |
| Edge Finish | Standard Factory Seamed |
| Country of Origin | Fabricated in the USA |
Appliance and R10 Pattern Cut Notice
R10 Pattern Cut Profile Only: This listing is specifically configured for asymmetrical door cavities defined by five distinct dimensional coordinates: overall width (Dimension A), total vertical height (Dimension B), left vertical run (Dimension C), right vertical run (Dimension D), and bottom flat width (Dimension E). If your door frame requires a curved crown, dual clipped corners, or custom notches, use our custom pattern quote form instead.
Appliance Exclusions: Never install Pyroceram ceramic glass on kitchen cooktops, range stoves, or standard open-hearth fireplace doors (such as zero-clearance prefab metal fireplaces) unless explicitly specified by the appliance manufacturer. Never substitute tempered glass on airtight heating stoves.
Measuring Instructions
Accurate multi-point field measurements ensure proper clearance across all five profile facets:
- Measure Dimension A (Total Width): Measure the maximum horizontal distance from the outer left vertical edge across to the outer right vertical edge.
- Measure Dimension B (Total Height): Measure the maximum vertical distance from the horizontal plane of the bottom edge up to the highest apex point at the top-left corner.
- Measure Dimension C (Left Vertical Run): Measure the straight vertical height along the left edge from the top corner down to where the lower-left corner bevel begins.
- Measure Dimension D (Right Vertical Run): Measure the full straight vertical height along the right outer edge from the flat bottom baseline up to the top-right corner.
- Measure Dimension E (Bottom Flat Width): Measure the flat horizontal span across the bottom edge from the bottom-right corner over to where the angled clip begins.
- Subtract 1/8" for Thermal Expansion: Deduct a full 1/8" (0.125") from your overall width (A) and total height (B) to prevent the glass from binding as the metal door frame expands under heat.
- Verify Intact Glass Dimensions (If Available): If your original glass is intact, cross-reference all 5 measurements (A, B, C, D, E) before submitting.
- Confirm Order Specifications: Double-check all inputs before checkout. Custom-cut pattern glass enters production immediately and cannot be modified once cutting begins.
Downloads & Helpful Resources
Manufacturer Warranty:
Fast Replacement Glass provides pyroceram ceramic glass to our customers based on specific size requirements. We warrant to our immediate customers that the glass product ordered will meet certain standards and will be free from material and workmanship defects on the day of shipment.
Fast Replacement Glass does not offer warranties on performance or customer use of the glass. How a customer handles, installs, and uses processes the glass product is solely the customer's responsibility. Fast Replacement Glass cannot be held liable for breakage, damage, or failure of the product due to wrongful installation or if the glass pane is too tight and doesn't allow for thermal expansion during operation of the heating appliance.
Estimated Lead Time:
Please give us 5 business days to create this product for you.
No reviews found